Just about everyone is bound to have his or her own way of thinking involving How to Install a Bathtub.
Mounting a tub isn't precisely rocket science, yet it does call for strong plumbing, carpentry, and occasionally, tiling abilities. Replacing an old bathtub with a brand-new one is additionally a moderately challenging project. If the old bathtub is easily available, the task can relocate rapidly; if you have to open up a wall to remove the old bathtub as well as position the brand-new tub, the task is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will require an assistant to move out the old bathtub as well as set in the brand-new one. Ensure you have certified yourself for the work as well as are comfortable trying it. Instead of hiring a service provider to take over a halfway-completed project, it is far better to consider using one before you start. Possibilities are you may require a professional plumber to make tube links.
This article will certainly help you mount a new bath tub in your restroom if you have actually currently bought a brand-new tub as well as don't require to change the plan of your previous water supply pipelines.
Your tools as well as material checklist should make up the following:
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installment, then the first thing you need to do is disconnect the water system. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The process of eliminating the existing faucets can be quite bothersome due to the restricted accessibility that is frequently the situation.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to undo the nut that links the supply pipelines to the taps. Have a fabric all set for the remaining water that will come from the pipelines. As soon as the supply pipes have been eliminated, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly require to stop the single faucets from transforming during this process. When the taps have been eliminated, the holes in the bath/basin will certainly need to be cleaned of any type of old securing substance.
Prior to moving on to fit the new faucets, contrast the pipeline connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will certainly require a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the tap as well as the various other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making sure that the washing machines remain in area in between the faucet and also the sink. Safeguard the faucet in position with the supplier provided backnut. Once the tap is securely in place, the supply pipes can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet ports. The former type needs to be attached to the faucet finishes initially, tightening up just by hand. The supply pipelines can later be linked to the other end. Tighten both ends with a spanner after both ends have been connected.
Installing the Bath tub
Making use of both wood boards under its feet, put the tub in the needed placement. The wood boards are handy in equally spreading out the weight of the tub over the area of the boards instead of focusing all the weight onto four little points.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by checking the spirit level and also readjusting the feet on the tub up until the spirit level reviews degree.
To set up taps, fit the bottom of the outermost adaptable faucet port to the suitable supply pipeline by making a compression sign up with; then do the same for the various other tap.
Activate the water system as well as check all joints and also brand-new pipework for leaks and tighten them if essential. Fill the bath tub and also examine the overflow outlet and the regular electrical outlet for leaks.
Ultimately, take care of the bath paneling as defined in the maker's instruction manual. Tiling and also securing around the bathtub must wait until the bath tub has been used at the very least once as this will certainly settle it into its last placement.
Getting ready for the Installation
To start with, the supporting structure supplied with the bathroom must be fitted (if needed) according to the producer's guidelines. Next, fit the faucets or mixer to the tub. When fitting the faucet block, it is important to make certain that if the tap includes a plastic washer, it is fitted in between the bathroom as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets device to prevent stress on the bath tub.
Fit the versatile faucet connectors to the bottom of the two faucets making use of 2 nuts as well as olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet through the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. See to it you utilize all of the supplied washers.
Link the catch to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link all-time low of the overflow tube in a comparable manner.The bath ought to now prepare to be suited its last placement.
Tiling Around the Bathtub
In the area where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the installation can relocate sufficient to fracture an inflexible seal, causing the water to permeate the wall surface in between the bath and the tiling, resulting in issues with dampness and feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, and also can securing voids approximately a size of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with spins of drenched newspaper or soft rope. Keep in mind to always fill up the bathtub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can split relatively very early if you do not take into consideration this motion before sealing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily readily available on the marketplace. It is recommended to fit the tiles using waterproof or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that piece on A Step-by-Step Guide to Installing a Bathtub when doing a search on the search engines. Sharing is good. Who knows, you may be doing someone a favor. We truly appreciate reading our article about How to Install a Bathtub Yourself.
Call Us Today